1.    New and Used Engines (Petrol and Diesel)

--  reduces petrol or diesel fuel consumption at idle up to 30% and up to 5% during driving;

--  increases petrol or diesel engine power and torque;

--  increased (up to 42.5%) and equalized compression in the cylinders;

--  ten fold decrease in concentration of CO and CH in exhaust (purification efficiency for CO is up to 24%, for CH up to 88%);

--  decreased of oil burn-out loss;

--  reconditions and protects moving parts against wear;

--  reduce friction coefficient up to 300 times;

--  lowered noise and vibration up to 10 times;

--  stabilized operation at any working conditions and regimes;

--  decreased of pollutant emission in the air;

--  extended protection in case of emergency oil leakage;

--  lower requirements to the oil quality and longer operation time between oil changes.

2.       New and used manual transmission gearbox and reducers

--  up to 15% fuel saving, especially in all-wheel drive cars.

--  lower gearbox transmission noise and vibration;

--  restoration of the geometry of gearbox gears and transmission bearings;

--  smoothing and filling up cavities.

3.       Hydraulic steering Boosters

--  reduce hydraulic steering back lash

--  increased useful life;

--  restores and reconditions worn-out metal parts;

--  reduced hydraulic steering humming and roar.

4.      Bearings and Equal Angular Velocity Articulated Joints

--  restoration of factory bearing specifications (dimensions and clearances) at about 80% wear;

--  no seizure of the unit;

--  resistance to the aggressive environment;

--  eliminates bearing ovality and conicity in reciprocating groups;

--  restores and reconditions worn out surfaces by up to 0,5 mm;

--  decreased noise and vibration level;

5.      Machinery, Equipment and Tools

--  restoration of the worn and decreased gaps in the rubbing pairs of bed slides, gearboxes, shafts and spindle units;

--  restores and reconditions machine tool accuracy of characteristics of the machine tools up to the specifications;

--  decreased machine tool noise and vibration level;

--  increased pressure and improved operation of the hydro system;

--  decreased energy consumption by up to 30%.

6.       Compressors

--  reduced gaps in compressors crank mechanisms;

--  eliminated ovality and conicity in reciprocating groups;

--  restored compressors worn out surfaces up to 0,5 mm;

--  increased oil pressure;

--  reduced operating temperature;

--  decreased noise and vibration level;

--  electric energy saving of up to 25%.

7.      Industrial Reducers, Gearboxes and Transmissions

--  restoration of worn parts, bearings and gears;

--  decreased gaps and clearances up to the optimal specification

--  increased the surface hardness (up to 600 kg/mm2) of the friction pairs, gear teeth and bearings;

--  decreased working temperature of the oil;

--  increased oil pressure;

--  reduced gearbox noise and vibration level;

--  restoration or worn out surfaces (up to 1,05 mm);

--  decreased energy consumption (by up to 35%).

8.       Industrial Blowers and Smoke Extractors

--  restoration of worn and decreased gaps between shaft and bearing;

--  reduced blowers and smoke extractor noise and vibration level;

--  restoration blowers and smoke extractor worn surfaces up to 0,05 mm;

--  save up to 15% of electric energy.

9.       Oil Pumps and Hydraulic Motors

--  increased pressure and raised efficiency;

--  decrease working temperature of the oil and hydraulic fluids;

--  restores and reconditions worn surfaces up to 0,1 mm of the parts, bearings and gears;

--  decreased gaps and clearances up to the optimal specification

--  increased the surface hardness (up to 600 kg/mm2) of the friction pairs, gear teeth and bearings;

--  increased pressure of the fluids;

--  decreased noise and vibration level, stabilized operation;

--  decreased energy consumption (by up to 35%).

10.    Presses, Hammers and Dies

--  increased pressure and raised efficiency;

--  decreased working temperature of the oil and hydraulic fluids;

--  restored worn-out surfaces up to 0,2 mm of the parts, bearings and gears;

--  decreased gaps and clearances up to the optimal specification

--  increased the surface hardness (up to 600 kg/mm2) of the friction pairs, gear teeth and bearings;

--  decreased working temperature and increased operating pressure of the fluids;

--  stabilized operation of the hydraulic system;

--  decreased noise and vibration level;

--  decreased energy consumption (by up to 30%).

  11.    Fuel Equipment (high pressure fuel pumps)

--  increased pressure and raised efficiency;

--  stabilized operation

--  decreased working temperature;

--  restored worn-out surfaces up to 0,1 mm of the parts, bearings and gears;

--  decreased gaps and clearances up to the optimal specification

--  increased the surface hardness (up to 600 kg/mm2) of the friction pairs, gear teeth and bearings;

--  increased pressure of the fluids;

--  decreased noise and vibration level;

--  fuel consumption and saving down to 15%.

12.    Rolling and Rounding Rolls

--  restored wear out of parts, bearings and gears;

--  decreased gaps and clearances up to the optimal specification

--  increased the surface hardness (up to 600 kg/mm2) of the friction pairs, gear teeth and bearings;

--  decreased noise and vibration level;

--  restored worn-out surfaces (up to 1,5 mm);

13.     Formers of Different Configuration

--  increased the surface hardness (up to 600 kg/mm2) of the friction pairs, gear teeth and bearings;

--  decreased noise and vibration level;

--  decreased energy consumption;

--  elimination of wear of the working surface of formers and probes;

--  elimination of micro-damages on the working surfaces of the formers;

--  reliable protection of the formers against aggressive medium;

--  long-term maintenance of preset accuracy of formers shape and dimensions.

14.    2 Stroke Engines

--  2 stroke Motor Cycles;

--  2 stroke Scooters;

--  2 stroke outboard Engines;

--  2 stroke Lawn mowers;

--  Blowers;

--  Trimmers;

--  Chainsaws;

--  Generators;

--  Any small engine

The treatment is exceptionally simple. You introduce the required amount of gel (grease) and then, under normal operating conditions, the result is achieved without the need for an expensive repair !!!